hydo said...
Sorry but i forgot how to post a new question and just jumped in this .
iam having a problem with gear pump witch is connected via a monoblock to a pressure guage.
problem is that when i switch the dcv 'on' the guage showes 190 bar ,but for just for one second
then it start to go doun to 100 bar and stay at 100 bar.
as i switch off and then on again
it goes to 150 and then goes down again.
is it relief walve which is releasing pressure and not settlig down again till pressure goes down to 100 bar , if it is pressure should rise again .can a pilot oprated relief solve this .
forgive me for a so basic and not mind frying question.
January 5, 2010 3:51 AM
Tuesday, January 5, 2010
Thursday, November 5, 2009
Snow Auger
Anonymous said...
I have a 36 inch snow auger that needs to be run at 900-950rpms. What size hydraulic pump and motor would i need to run it. I have a 2 cylinder 13hp honda gas motor that i am going to use to power it.
I have a 36 inch snow auger that needs to be run at 900-950rpms. What size hydraulic pump and motor would i need to run it. I have a 2 cylinder 13hp honda gas motor that i am going to use to power it.
Thursday, September 3, 2009
Log Splitter Valve
Anonymous said...
I am building a log splitter with a log lift. I have two single spool log splitter valves with detents. Can I use them both in tandem? If so is there anything besides the hose between them needed to do it?
August 21, 2009 4:04 PM
I am building a log splitter with a log lift. I have two single spool log splitter valves with detents. Can I use them both in tandem? If so is there anything besides the hose between them needed to do it?
August 21, 2009 4:04 PM
Impulse Test Flow Rate
Valliappan said...
I wanted to do impulse test on a cylinder in fully retracted condtion. Cylinder size Bore 100mm, Rod 60 mm, stroke 1000mm. The annular volume is 5.026 ltrs. The pressure has to be rised from zero to 410 bar in 60 mill sec and brought back to zero (sinosoidal wave). We have to do impulse at the rate of 8Hz. What will be the pump flow reqd to this impulse test assuming the cylinder is initially filled with oil and the pump is reqd to rise the pressure to 410 bar.
August 19, 2009 1:53 AM
I wanted to do impulse test on a cylinder in fully retracted condtion. Cylinder size Bore 100mm, Rod 60 mm, stroke 1000mm. The annular volume is 5.026 ltrs. The pressure has to be rised from zero to 410 bar in 60 mill sec and brought back to zero (sinosoidal wave). We have to do impulse at the rate of 8Hz. What will be the pump flow reqd to this impulse test assuming the cylinder is initially filled with oil and the pump is reqd to rise the pressure to 410 bar.
August 19, 2009 1:53 AM
Stopping a Cylinder When Pressure is Lost
NL SONI said...
IT IS REQUIRED TO LOCK A VERTICAL SERVO HDRAULIC LINEAR ACTUATOR HANDLING A DEAD WEIGHT WHENEVER A LOSS OF PRESSURISED OIL SUPPLY TO THE ACUATOR. IT SHOULD INSTANTLY STOP AND GET LOCK AT THE SAME POSITION AT THE TIME OF OIL SUPPLY FAILURE.THE OPERATING PRESSURE IS ABOUT 20 BAR TO 100 BAR.KINDLY SUGGEST THE WORKABLE SOLUTION FOR THIS REQUIREMENTS.
August 18, 2009 9:26 PM
IT IS REQUIRED TO LOCK A VERTICAL SERVO HDRAULIC LINEAR ACTUATOR HANDLING A DEAD WEIGHT WHENEVER A LOSS OF PRESSURISED OIL SUPPLY TO THE ACUATOR. IT SHOULD INSTANTLY STOP AND GET LOCK AT THE SAME POSITION AT THE TIME OF OIL SUPPLY FAILURE.THE OPERATING PRESSURE IS ABOUT 20 BAR TO 100 BAR.KINDLY SUGGEST THE WORKABLE SOLUTION FOR THIS REQUIREMENTS.
August 18, 2009 9:26 PM
Saturday, March 14, 2009
Suction Line Oil Level
I borrowed this topic from the H & P Forum but I have seen some discussion about my posts:
If positive displacement pump is running and stopped , pump is mounted on tank and suction length above oil level is 200 mm and there is no leakage in suction line and suction chamber ,whether the oil will remain full in suction line after pump stoppage . Will it fall down ?
What happens if length is 400 mm, 800 mm, etc.
If positive displacement pump is running and stopped , pump is mounted on tank and suction length above oil level is 200 mm and there is no leakage in suction line and suction chamber ,whether the oil will remain full in suction line after pump stoppage . Will it fall down ?
What happens if length is 400 mm, 800 mm, etc.
Monday, February 23, 2009
Piston Seal Leakage - Rod Down
We have a cylinder mounted with the rod pointing down. It has a weight on the end of the rod.
There is a ball valve at each cylinder port.
Assumptions:
There is a ball valve at each cylinder port.
Assumptions:
- Piston seals are leaking badly
- Rod seal does not leak
- Ball valves, when closed, do not leak
What happens when the cylinder is fully retracted and both ball valves are closed?
Subscribe to:
Posts (Atom)